Measurement-computing DBK Part 2 Uživatelský manuál Strana 149
- Strana / 306
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
The excitation output voltage is set via JP2.
JP2 Location Reference
The above figure is of a partial DBK80. JP2 is shown selected to +5VDC. Note that the card’s overlay for
JP2’s voltage selection, also depicted in the figure, indicates the jumper positions that are required to select
the +5 or +10 VDC excitation output.
DaqBook/100 Series & /200 Series and DaqBoard [ISA type] Configuration
Use of a DBK80 with a DaqBook/100 Series & /200 Series devices, or with an ISA-type DaqBoard,
requires the configuration of jumpers JP1 and JP4 located on the DaqBook/100 Series & /200 Series
devices, or DaqBoard [ISA type], as applicable.
1. If not using auxiliary power, set the JP1 jumper for Analog Option Card Use,
also referred to as the expanded analog mode.
Note:
These jumpers do not
apply to /2000 Series
Devices.
Required Jumper Settings in DaqBook/100 Series & /200 Series
and ISA-Type DaqBoards
The JP1 default position (above) is necessary to power the interface circuitry of the
DBK80 via the internal ±15 VDC power supply. If using auxiliary power (e.g.,
DBK32A or DBK33) you must remove both JP1 jumpers.
Refer to Power Requirements in the DBK Basics section and to the DBK32A and
DBK33 sections for more detailed information, as applicable.
2. For DaqBook/100, DaqBook /112, and DaqBook /120 only, place the JP4 jumper in the single-ended
mode.
Note: Analog expansion cards convert all input signals to single-ended voltages that are referenced to
analog common.
DBK Option Cards and Modules 989494 DBK80 pg. 5
- *372414B-01* 1
- DBK Cards & Modules 3
- DBK Cards & Modules 5
- Discontinued DBKs 6
- 10-Slot Expansion Module 7
- Card Insertion 9
- DBK41 - Specifications 11
- System Connection 11
- Terminal Block Connection 15
- 967694 DBK42, pg. 5 17
- This means: m = 320 19
- DBK42 – Specifications 20
- Configuration section 22
- Hardware Connection 23
- Hardware Configuration 24
- Bridge Applications 26
- MAX[EXC] 27
- Input Configuration Headers 29
- Shunt-Calibration Resistors 29
- Hardware Adjustment 33
- Software-Controlled Setup 34
- Selecting DBK43A 42
- Calibration Methods 46
- Determine Channel Parameters 47
- Initialize LogView 47
- know [as in the 50
- See Note No 52
- Adjust the Offset 53
- 2-Point Calibration 56
- Repeating the Process 57
- Shunt Calibration 58
- )( trimpotbysetasGainInput 62
- DriftOffsetOutput 62
- DriftOffsetInput + 62
- P1 Connection 66
- 877095 DBK44, pg. 7 69
- DBK44 – Specifications 70
- 987696 DBK45, pg. 3 73
- DBK45 – Specifications 76
- 4-Channel Analog Output Card 77
- DBK46 – Specifications 80
- Description 81
- Safety Concerns 82
- Installing 8B Modules 84
- 967792 DKB48, pg. 11 91
- This means: m = 320 95
- Therefore: b = - 160 95
- Specifications – DBK48 96
- 8B Module Ranges 97
- 967792 DKB48, pg. 19 99
- Overview 101
- Hardware Setup 102
- DAC 1 - INT 103
- Software Setup 104
- Single-Ended Mode 107
- Module Connection 107
- Module Configuration 107
- 989594 DBK55, pg. 1 111
- Input Signal Conditioning 113
- WARNING 113
- CAUTION 114
- Edge Selection 114
- Debouncing 114
- Frequency Measurement 115
- 988793 DBK55, pg. 7 117
- CE Compliance 120
- Specifications - DBK55 122
- 3 – Remove the card drawer 125
- 8 – Configure the DBK cards 127
- 9 – Install the DBK cards 127
- DBK60 - Specifications 128
- DBK65 Power Requirements 130
- DBK65 Voltage Regulation 130
- Customizing a Voltage 132
- Source Resistance in Ohms 134
- These jumpers do 136
- Series Devices 136
- 988793 DBK65 pg. 11 139
- DBK65 Specifications 140
- 988793 DBK65 pg. 13 141
- Vehicle Network Interface 143
- 989494 DBK80 pg. 3 147
- Card Configuration 148
- These jumpers do not 149
- Devices 149
- DBK80 - Specifications 150
- Open Thermocouple Detection 153
- POD-1 Dimensions 155
- TC Accuracy 159
- 989494 DBK84 pg. 7 167
- DBK84 - Specifications 168
- CE Compliance …… 4 169
- Specifications – DBK85 174
- 907492 DBK90 pg. 1 175
- 907492 DBK90 pg. 5 179
- 907492 DBK90 pg. 7 181
- 907492 DBK90 pg. 9 183
- Shielding 184
- TC Common Mode 184
- DBK90 – Specifications 187
- Description Part No 188
- DBK101 Hub Configuration 195
- TC Common Mode 198
- DaqBook/2000 Series Users: 205
- P4-to-P1 / P2 / P3 Adapters 207
- Screw-Terminal Adapter Board 209
- Connection Tips 210
- Using Screw-Terminal Blocks 212
- Using the P3 Header 217
- Connections 222
- P4-to-P1/P2/P3 Adapter Board 223
- 987594 DBK206, pg. 3 225
- 987594 DBK206, pg. 5 227
- 5B Carrier Boards 229
- Warnings, Cautions, and Tips 231
- External Ground Connection 232
- Channel Configuration 233
- 5B Module Connection 233
- DBK208 Relay Carrier Board 237
- DBK208, pg. 4 240
- External Power Watchdog 241
- Operation 241
- Switch Settings 244
- For Digital Output 244
- For Digital Input 244
- DBK208 – Specifications 245
- DBK208, pg. 10 246
- 909094 DBK209, pg. 3 249
- DBK209, pg. 4 250
- 987594 DBK210, pg. 3 253
- 987594 DBK210, pg. 5 255
- DBK210, pg. 6 256
- DBK210, pg. 8 258
- DaqView’s Channel Setup Tab 259
- In the above figure t 259
- DBK210 – Specifications 260
- Installing DBK Cards 263
- System Examples 264
- Example 2: 265
- 969294 DBK213, pg. 7 267
- 969294 DBK213, pg. 9 269
- 969294 DBK213, pg. 11 271
- Specifications for DBK213 272
- 969294 DBK213, pg. 13 273
- DBK213, pg. 14 274
- DBK214, pg. 2 276
- 279
- DBK214, pg. 6 280
- [2 Screws per-side] 280
- 967894 DBK214, pg. 7 281
- 967894 DBK214, pg. 9 283
- 967894 DBK214, pg. 11 285
- 967894 DBK214, pg. 13 287
- Specifications for DBK214 288
- 967894 DBK214, pg. 15 289
- DBK214, pg. 16 290
- DBK215, pg. 2 292
- System Example 294
- 897994 DBK215 pg. 7 297
- 897994 DBK215 pg. 9 299
- DBK215, pg. 12 302
- Specifications for DBK215 303
- DBK215, pg. 14 304
Související produkty a manuály pro Hardware Measurement-computing DBK Part 2
Hardware Measurement-computing DBK70 Uživatelský manuál
(108 stránky)
(108 stránky)
Vixen Collimating your VC200L or VMC200L podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia optyczne Vixen Collimating your VC200L or VMC200L.
Dostarczamy 1 pdf podręczników Vixen Collimating your VC200L or VMC200L do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce