Measurement-computing Analyzer488 Uživatelský manuál Strana 59
- Strana / 281
- Tabulka s obsahem
- KNIHY
- Analyzer488 1
- User's Manual 3
- Table of Contents 10
- Introduction 13
- Section 1 Introduction 14
- Analyzer RAM Error 20
- Analyzer ROM Error 20
- Analyzer NVRAM Error 21
- Serial Controller 21
- Instrument Simulator 21
- BUS 'A' 41 ¼ 21
- Getting Started 23
- Analyzer488 Rev 1.0 24
- BUS DCL 14 • 24
- Section 2 Getting Started 25
- LOCATION MESSAGE 25
- Config Reset? No 27
- Config Reset? Yes 27
- Trigger Sequence Flow Chart 35
- Handshake 42
- Front Panel Operation 47
- Factory Config? No 48
- Config? Front Panel 48
- LOCATION 49
- Invalid Key Press 53
- Save Macro? 54
- BUS ACG00 00 56
- When Completed? Stop 61
- Data Entry Keys 73
- Save Macro? X 74
- Saving to Macro X 74
- End Saving Keys 74
- Select Key for Help 74
- Cursor Keys 75
- Record Memory Erased 78
- Reset Memory? Yes 78
- Record Memory Reset 78
- Reference Set 79
- -SEARCH 79
- Not Available 79
- +Searching 79
- Trigger Not Found 79
- Pattern Not Found 80
- Last 00000 83
- Display Intensity 32 83
- Help Scroll Speed 6 83
- Match? Nul XXXXXXX 83
- Match? XXXXXXXXXXXXX 84
- # of Matches? 00001 84
- Trig Delay? 0000000 84
- Post Count? 00000 84
- When Complete? Stop 84
- Time 0.000 mSeconds 85
- Count 00000 Bytes 85
- Rate 0.000 B/sec 85
- Display Hex Data 86
- Display Binary Data 86
- Steps Per second 03 88
- Handshaking Off 88
- LISTEN TALK 89
- Printer Stop Bits? 2 91
- Printer Parity? None 91
- Printer Ctrl? RTS/CTS 91
- Print Terms? CR 91
- Printer Address? 16 91
- Print Terms? CR 92
- EOI ATN SRQ REN IFC 93
- Section 4 Serial Controller 100
- 110
- CONTROLLER 118
- HANDSHAKE 130
- LOCAL LOCKOUT 138
- PPOLL CONFIG 146
- PPOLL DISABLE 148
- PPOLL UNCONFIG 149
- ? (PRINT) 150
- RELATIVE 156
- SET RELATIVE 164
- SET TRIGGER 165
- UNASSERT 183
- Analyst488 Software 189
- Section 5 Analyst488 Software 190
- W3 Noise 240
- W11 f(t)=Sin(wt) 244
- Front Panel Keys 251
- Serial Controller Commands 255
- Instrument Simulator Commands 259
- Analyst488 Software Menus 263
- Analyzer488 Error Messages 265
- Sample BASIC Program 267
- IEEE 488 Primer 269
- Appendix G IEEE 488 Primer 270
- IEEE 488 Bus Structure 271
- Figure 4.1 271
Související produkty a manuály pro Hardware Measurement-computing Analyzer488
(2 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce