Measurement-computing Personal Daq rev.6.0 Uživatelský manuál Strana 13
- Strana / 170
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Personal Daq User’s Manual
878395 Unit Startup 1-5
CAUTION
Never remove a USB cable from an active Personal Daq device while an acquisition is
in progress. An active device is any device that is currently open and has channels
configured for scanned input. Such disconnection may require you to exit and then
re-launch Personal DaqView, after the USB cable has been connected.
If you are going to install a PDQ expansion module:
1. Ensure that no power cable or USB cable is connected to the main unit
2. Plug the expansion module into the DB25 connector-end of the Personal Daq main unit
3. Lock the modules together with two locking clips (provided). Refer to the previous figure.
Connect Personal Daq to Host PC
When using a power adapter with your Personal Daq system, be sure to supply power
(from the adapter to the Personal Daq) before connecting the USB cable. This allows
Personal Daq to inform the host computer (upon connection of the USB cable) that the
unit requires minimal power from the computer.
Use an approved high-speed USB cable to connect the Personal Daq system to one of the host computer’s
USB ports. There is no need for an additional power source in this setup since the power pins (of the PC’s
USB connection) supply 500 mA at 4 to 5.25 V. Additional setup examples are described in Chapter 3,
some of which involve USB hubs and/or power adapters.
Connection of a Simple Personal Daq System to a Computer USB Port
Certain notebook computers require the use of a power adapter with your Personal Daq.
- User’s Manual 1
- Personal Daq 1
- 491-0901 4
- 1086-0926 4
- 1086-0922 4
- About This Manual 5
- Table of Contents 7
- 5 – Signal Management 8
- 6 - Calibration 8
- Unit Startup 1 9
- Install Software 10
- Install Hardware 10
- Personal Daq User’s Manual 11
- Unit Startup 1-3 11
- 1-4 Unit Startup 12
- Personal Daq User’s Manual 12
- CAUTION 13
- Start Personal DaqView 15
- Configure System 16
- Channel Configuration 17
- Acquisition Configuration 17
- Collect Data 18
- PDAQ.BIN, is as follows: 19
- No Expansion 21
- ---- N/A ---- ---- N/A 21
- Features 22
- Theory of Operation 23
- Optical Isolation 24
- A/D Conversion 24
- Input Ranges 24
- Analog Input Configuration 25
- Automatic Calibration 27
- Thermocouple Measurements 27
- Analog Specifications 30
- Input Voltage Ranges 30
- Thermocouple Accuracy 31
- General Specifications 32
- Optional Accessories 32
- Channel Connection Layouts 33
- Calibration 35
- Hardware Setup 3 37
- PDQ Expansion Modules 38
- USB Hubs and Power Adapters 39
- 3-4 Hardware Setup 40
- Hardware Setup 3-5 41
- 3-6 Hardware Setup 42
- Main Control Window 45
- Pull-Down Menus 46
- Measurement Units 47
- Channel Configuration Window 48
- Common Spreadsheet Columns 49
- (b) for the application in 50
- cell for PD1_A01, typed 51
- Analog Input Spreadsheet 52
- Measurement Duration Column 53
- Resolution and Settling Time 55
- 4-14 Personal DaqView 56
- The Trigger Section 58
- Averaging 58
- Acquisition Parameters 59
- 4-18 Personal DaqView 60
- Why use Auto Rearm? 61
- Disabling Auto Rearm 61
- Meter Toolbars 62
- Meter Pull-Down Menus 63
- Meters Configuration Menu 63
- Configuring a Meter 64
- Bar Graph Meters 66
- Analog Meters 67
- Digital Meters 68
- Chart Display 69
- Toolbar Items 71
- Item Description 72
- 4-34 Personal DaqView 76
- 4-36 Personal DaqView 78
- Chart Setup Wizard 79
- 4-40 Personal DaqView 82
- System Requirements 84
- Installation 84
- First Time Use 84
- Configuration Reference 87
- Auto-Load Function 90
- Real-Time Charting 93
- Data Header 94
- Hints and Tips 95
- Signal Acquisition 100
- Triggering 101
- Signal Modes 102
- System Noise 103
- Input and Source Impedance 104
- Crosstalk 104
- Analog Filtering 104
- Introduction 105
- Required Equipment 106
- Calibration Procedure 106
- 878395 Calibration 6-3 107
- 878395 Calibration 6-5 109
- Radio Frequency Interference 111
- Troubleshooting 112
- Customer Assistance 115
- Appendices 117
- Overview 119
- Data Acquisition Environment 119
- Programming Models 120
- Read 1 sample from multiple 122
- Buffers 125
- Multiple Channel Types 128
- API Commands B 133
- (Does not apply to 161
- Personal Daq/54) 161
- Note: Includes “NE” version 163
- Table 9. API Error Codes 165
- 83h - 131 166
Související produkty a manuály pro Hardware Measurement-computing Personal Daq rev.6.0
(26 stránky)Vixen Collimating your VC200L or VMC200L podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia optyczne Vixen Collimating your VC200L or VMC200L.
Dostarczamy 1 pdf podręczników Vixen Collimating your VC200L or VMC200L do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce