Measurement-computing PCI-DIO48H/CTR15 Uživatelský manuál

PCI-DIO48H/CTR15Digital I/O & CountersUser’s ManualRevision 2March, 2001

state). We recommend using 2.2 K SIPs on the digital output pins. You will findpositions for pull up and pull down resistor packs on the board. For mo

5 I/O REGISTER MAPSThe PCI-DIO48H/CTR15 uses eight standard I/O addresses for the two 8255emulations, 20 addresses for the five 82C54s (4 each) as wel

5.1 PCI-DIO48H/CTR15 REGISTER DESCRIPTIONINTERRUPT STATUS/CONTROLBADR1 + 4ChREAD/WRITEINTEINTPOLINTxxxxxx0123456731:8This register, as with all the 90

CONTROL REGISTER 1BADR2 + 03hWRITE onlyD0D1-D3D4---01234567The operating mode of the digital I/O ports is Mode 0. The control register thereforeis us

PORT 2C DATABADR2 + 06hREAD/WRITECL0CL1CL2CL3CH0CH1CH2CH301234567CONTROL REGISTER 2BADR2 + 07hWRITE onlyD0D1-D3D4---01234567See BADR2 + 03h and Table

First the low byte is written, then the high byte. The Control Register is 8-bits wide.Further information can be obtained on the 82C54 data sheet, av

COUNTER 9 DATABADR2 + 12hREAD/WRITED0D1D2D3D4D5D6D701234567CONTROL REGISTER COUNTERS 7 - 9BADR2 + 13hWRITE ONLYD0D1D2D3D4D5D6D701234567See BADR2 + 0Ch

COUNTER 13 DATA BADR2 + 18hREAD/WRITED0D1D2D3D4D5D6D701234567COUNTER 14 DATA BADR2 + 19hREAD/WRITED0D1D2D3D4D5D6D701234567COUNTER 15 DATABADR2 + 1AhRE

6 SPECIFICATIONSTypical for 25°C unless otherwise specified. POWER CONSUMPTION+5V Operating 1395 mA typical, 2091 mA maxDIGITAL INPUT/OUTPUTDigital T

82C54B:Counter 0 - User counter #4Source: Available at user connector (CTR4CLK)Gate: Available at user connector (CTR4GATE)Output: Available at user

MEGA-FIFO, the CIO prefix to data acquisition board model numbers, the PCM prefix to dataacquisition board model numbers, PCM-DAS08, PCM-D24C3, PCM-DA

Counter 1 - User counter #14Source: Available at user connector (CTR14CLK)Gate: Available at user connector (CTR14GATE)Output: Available at user conn

7 ELECTRONICS AND INTERFACINGThis short introduction to the electronics, most often needed by digital I/O boardusers, covers a few key concepts.IMPORT

Of course, a pull-down resistor accomplishes the same task except that the line ispulled low when the board is reset and the output has more than enou

SSRs. If you have only a few outputs to control, you may also wish to consider theDR-OAC or DR-ODC, single point, DIN mountable SSRs. The high current

For a given attenuation, pick a handyresistor and call it R2, then use thisformula to calculate R1.R1 = (A−1) x R2Digital inputs often require voltage

For your notes21

For Your Notes22

EC Declaration of ConformityWe, Measurement Computing Corporation, declare under sole responsibility that theproduct:DescriptionPart NumberDigital I/O

Measurement Computing Corporation16 Commerce Boulevard,Middleboro, Massachusetts 02346(508) 946-5100Fax: (508) 946-9500E-mail: info@measurementcomputi

Table of Contents217.3 VOLTAGE DIVIDERS ...207.2 TTL TO SOLID STATE RELAYS ...197.1 PULL UP &

This page is blank,

1 INTRODUCTIONThe PCI-DIO48H/CTR15 is a multifunction, logic level, digital I/O board forcomputers that implement the PCI bus. The board offers a powe

InstaCal will show you any available options. It will create a configuration file thatyour application software (and the Universal Library) will refer

3 I/O CONNECTIONS3.1 CONNECTOR DIAGRAMThe 100-pin, high-density connector is accessible through the computer’s expansionbracket (Figure 3-1). The outp

The I/O connections can be brought out to easy-to-use screw terminals by purchasinga CFF100-series cable and two CIO-MINI50 screw terminal boards. The

See Figure 3-3 for a translation diagram of the upper half (pins 51 to 100) of theC100FF-xx cable to the second 50-pin connector.Figure 3-3. C100FF-xx