Measurement-computing eZ-TOMAS rev.11.0 Uživatelský manuál Strana 66
- Strana / 94
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Orbit Displays
Orbit Displays show simultaneous time domain vibration amplitude for an X and Y probe pair.
The location of each Tach pulse is shown on the orbit plot using black circles; and a rotation direction label
("CCW" or "CW") is shown next to these (see figure).
The default display is “Full Block” of time data. However, a specific number of Shaft Revolutions can be
displayed (1, 2, 5, or 10) by using the associated pull-down list (see figure). The orbit display is corrected
for probe location.
You can optionally overlay the orbit onto a shaft center line display by clicking the Shaft Centerline
button. The center of the orbit trace in SCL computes the difference between the current gap voltage and
the reference gap voltage. Information regarding shaft centerline plots is presented on page 7-9.
To display an overlay of the bearing circle clearance, as indicated below (third plot), click the
<Overlay Bearing Clearance Circle> button (see figure).
Note: Only one probe pair can be shown on the Orbit Display.
Orbit Shaft Shaft
Display
Centerline Revolutions
(see pg. 7-9) Filter (Note 1)
Display
Cursor
Values
Cursor
Update
(Peak
Search)
Overlay
Bearing
Clearance
Circle
Three Orbit Plots and a Time Waveform Plot Display
In this figure the plot at the upper right has focus.
7-4 Display Menu … Plots Plot Examples 937594 eZ-TOMAS
- User’s Manual 1
- Table of Contents 3
- 937694 eZ-TOMAS 4
- Introduction 1 5
- Starting eZ-TOMAS 6
- Connecting Signals 6
- The Order of Operation 7
- 987294 eZ-TOMAS 10
- The Spectral Bands and Tachs 11
- 889895 eZ-TOMAS 12
- Monitoring a Machine 2 15
- Using “Initialize Project” 16
- Using “New (Clone) Project” 18
- Configuring the Project 19
- Viewing Spectral Bands 20
- Plotting Data 20
- Starting an Acquisition 20
- “Real Time” Plot Controls 21
- “History Data” Plot Controls 22
- Viewing Reports 23
- 987294 eZ-TOMAS 24
- [In Gauge Window] 3 25
- Open Project 26
- Save As 26
- Time History data 27
- Erase History Data 28
- Erase Alarm Log 28
- Setup…… 29
- 947394 eZ-TOMAS 30
- 947394 Edit Menu 4-3 31
- Input Channels Tab 32
- 947394 Edit Menu 4-5 33
- XY Pair 34
- Tachometer Notes 35
- Counter Mode 36
- Period Mode 36
- Voltage Mode 36
- Spectral Bands Tab 37
- Storage Tab 38
- 947394 Edit Menu 4-11 39
- Limits 40
- Gauges and Mouse-Clicks 41
- 947394 Edit Menu 4-15 43
- 947394 Edit Menu 4-17 45
- Digital I/O Configuration 46
- 947394 Edit Menu 4-19 47
- [in Edit Menu] 48
- 947394 Edit Menu 4-21 49
- Copy Window 50
- Reset Peak Hold Values 50
- Display Menu . . . Plots 5 51
- 947294 eZ-TOMAS 52
- Channels 57
- Filtering Data 58
- Toolbar Buttons 6 59
- Toolbar 60
- Toolbar (continued) 61
- 937694 eZ-TOMAS 62
- Time Waveform Displays 64
- Spectrum Displays 65
- Orbit Displays 66
- Bode Displays 68
- Polar Displays 69
- Strip Chart Displays 70
- Shaft Center Line (SCL) 71
- 937594 eZ-TOMAS 72
- Statistical Report 73
- 947494 eZ-TOMAS 74
- Alarm Log 76
- Snapshot Log 77
- Interpreting the Report 85
- [.txt File] 87
- [In Gauge Window] 9 89
- Connecting to a Network Node 89
- Network Status Messages 89
- Disconnecting a Network Node 89
- [In Gauge Window] 10 91
- 897696 A-1 93
- Customization 94
Související produkty a manuály pro Hardware Measurement-computing eZ-TOMAS rev.11.0
(42 stránky)Vixen Collimating your VC200L or VMC200L podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Urządzenia optyczne Vixen Collimating your VC200L or VMC200L.
Dostarczamy 1 pdf podręczników Vixen Collimating your VC200L or VMC200L do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentáře k této Příručce