Measurement-computing DaqBoard 3000USB Series Uživatelský manuál Strana 30
- Strana / 128
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
1-4 Device Overviews
988093 DaqBoard/3000USB Series User’s Manual
Connections
SCSI - 68 pin (P5)
The 68-pin SCSI connector includes pins for the following. Chapter 2 includes a pinout.
o 16SE / 8DE analog
inputs (Ch 0 thru 15)
o 24 digital I/O
o 4 counter inputs
o 2 timer outputs
o A/D pacer clock I/O
o DAC pacer clock I/O
o TTL trigger
o
self calibration
+5 VDC
o
o analog commons
o digital commons
o up to four DACs (according to
board model)
You can connect a TB-100 screw-terminal board or a DBK215 BNC screw-terminal
module to the SCSI connector via one of the following cables.
CA-G55
CA-G56
CA-G56-6
68-conductor ribbon expansion cable. 3 feet.
68-conductor shielded expansion cable. 3 feet.
68-conductor shielded expansion cable. 6 feet.
40-pin Headers
(J5, J6, J7, J8)
Four 40-pin headers (J5 through J8) provide an alternative connection to the signals of the
SCSI connector. Also, for the /3031USB and /3035USB, the J5 and J6 headers accept
additional analog input for a total of 64 Single Ended, or 32 Differential. You can obtain a
male DB37 connector for each header by connecting a CA-248 (40-pin to male DB-37
cable) to each header.
9-slot Screw
Terminal (TB7)
The on-board screw terminal connector (TB7) can be used to connect up to four
thermocouple inputs. TB7 uses the following analog channels [which can also be
accessed via the SCSI connector and J5] to obtain its 4 differential channels:
TC CH0: CH 0 (+); CH 8 (-) TC CH1: CH 1 (+); CH 9 (-) TC CH2: CH 2 (+); CH 10 (-)
TC CH3: CH 3 (+); CH 11 (-)
As stated in the WARNINGS of the pinout and connection chapter
(Chapter 2), care must be taken to avoid redundant connections!
External
Power
Although the 3000USB Series boards are powered via a USB port on a host PC, an
external power connector is available for cases in which the host PC’s USB port cannot
supply adequate power, or for when the user prefers a separate power source. The TR-2
is an optional power supply available for this purpose. The TR-2 plugs into a standard
120VAC outlet and will supply 9VDC, 1 amp power to the board via its external power
connector (see figure).
40-Pin Headers 4 Channel TC
J6 and J5 Terminal Board (TB7)
SCSI (P5) External Power USB 2.0 Port 40-Pin Headers
68-Pin J8 and J7
Location of Connectors
- DaqBoard/3000USB Series 1
- 938390 5
- *324401C-01* 7
- Contents 9
- (1) Install Software 10
- 968492 IG-5 11
- 968492 IG-7 13
- How to Mount the TB-101 15
- Scenario 4: Using a DBK215 16
- 68-Pin SCSI Connecter 18
- XAPCR = A/D Pacer Clock I/O 20
- -- X-- = Not Connected 20
- 20
- 968492 IG-15 21
- (3) Start DaqView 22
- (4) Configure the System 23
- (5) Collect Data 24
- Customer Assistance 25
- Device Overviews 1 27
- Block Diagrams 28
- Connections 30
- Product Features 31
- 1-6 Device Overviews 32
- 1-8 Device Overviews 34
- 1-10 Device Overviews 36
- Solution: 37
- Example: 37
- 1-12 Device Overviews 38
- Calibration 39
- Analog Output 39
- 1-14 Device Overviews 40
- Counter Inputs 42
- Timer Outputs 42
- 1-18 Device Overviews 44
- Connections and Pinouts 2 45
- 68-Pin SCSI Connecter (P5) 46
- TB-101 Terminal Board Option 51
- TB-101 Pinouts 52
- Hardware Setups 56
- Scenario 2: Using a TB-100 57
- Scenario 3: Using a DBK215 58
- Safety Conditions 59
- 949290 User’s Manual 60
- Calibration 4 61
- Counter Input Modes 5 63
- Encoder Mode (see page 15) 68
- Counter/Totalize Mode 68
- Period Mode 70
- Pulsewidth Mode 73
- Timing Mode 75
- Encoder Mode 77
- Wiring for 1 Encoder 80
- Criteria 84
- Input Signal is Equal to X 84
- Driven by Condition 84
- Detecting Input Values 85
- See the TIP below 85
- The Setpoint Status Register 93
- DaqBoard/3000USB Series 7 95
- Analog Inputs 96
- AutoZero Disabled 97
- Type T thermocouple 98
- A/D Specifications 99
- Input Sequencer 99
- Triggering 100
- Digital I/O 101
- Pattern Generation Output 102
- Counters 102
- Frequency/Pulse Generators 103
- Software 103
- Accessories and Cables 104
- Dimensions 105
- Overview 107
- DBK215, pg. A-2 108
- 886994 Appendix A 108
- TB16 Supports BNCE thru BNCF 108
- Connection Tips 109
- System Examples 110
- WARNING ! 111
- DBK215, pg. A-6 112
- [2 Screws per-side] 112
- 886994 DBK215 A-7 113
- 886994 DBK215 A-9 115
- 886994 DBK215 A-11 117
- WARNING 118
- CAUTION 118
- 886994 DBK215 A-13 119
- Specifications for DBK215 120
- Signal Modes 121
- 938390 Appendix B 122
- Shielding 123
- TC Common Mode 123
- Analog Filtering 125
- Input and Source Impedance 125
- Crosstalk 125
- Glossary 127
- 887194 Glossary 128
Související produkty a manuály pro Hardware Measurement-computing DaqBoard 3000USB Series
(74 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce